• VARIABLE RESOLUTION
    Option to scan with 100-1,000 dpi, in light boxes up to 2,700 dpi

    The scanner head and its lens can be varied in their height, depending on the type of scanner, so that different resolutions can be “driven” between about 240 and about 530 or 1,000 dpi, depending on the size of the size of the model


    You can compare a 300dpi scan with a 1000dpi scan directly in our Viewer. Zoom in to maximum on both sides and experience the difference.

    option_var_res_compare

  • VARIABLE TEXTURE EFFECT
    Option for different capturing of textures (surfaces) in order to increase the plasticity

    The normal exposure mode L + R enables an equal illumination of the model without making the textures visible, if these are not desirable. The Standard Texture effect allows a one-sided exposure with the left or right lamp of the model amp center position so that a texture effect can be achieved. Furthermore, the Variable Texture effect allows a normal texture by moving the left or the right lamp 5 cm, 10 cm, 15 cm from the middle to strengthen, where appropriate, to increase the “drama” of the textures clear. The further it is from the center, the shallower the angle of exposure and the more shadow is created at the textures.


    You can get a first impression of the possibilities of this option in our viewer.

    Variabler Textureffekt - Multi Viewer

  • VARIABLE SCANNING SPEED
    Depending on scanning mode and light exposure conditions, it enables an increase of the scanning speed up to a factor 4

    This option of a hardware / software combination allows an adjustment of the selection of different scan times, depending on the original type and the selected scan mode.

    Depending on the scanning mode, this option allows a faster reading of the scan line, so that a scan time reduction can be achieved and adjusted from factor 1-4. – deepening on model type and required or desired quality requirements.

  • VARIABLE ANGLE REPRODUCTION
    Option for receiving originals at a defined viewing angle up to 15 °

    The complex option includes a movable CCD line, in order to achieve the desired angular reproduction position from 5 ° to reach 10 ° to 15 ° in the scanning head. This option is supplemented by a much longer path of the supporting table. To do so, much longer spindles are being used.

    With this supplementary equipment, the light fitting can be moved into the correct position automatically, without any intervening of the operator.

    Due to the consistently same “viewing angle” of the scan line, absolutely identically conditions are safeguarded from beginning to end of the scan path. Therefore, additional Texture effects can be achieved or desired or unwanted reflections can be scanned as well.

  • REAR LIGHT
    With Rear Light, texture effect of the original scan data can be reinforced

    This additional lamp provides a harsh shadow and therefore illustrates each immersion. The result is a dramatic 3 D that can then be adapted to specific requirements by using the Image Stacking with other scans effect. This option is particularly interesting for customers working in the decorative sector or service.


  • LIGHT ANGLE DEVICE
    Option for specific illumination of large models whose structures from shall be displayed in X and Y directions

    The light angle device allows that e.g. a light from the left side can be directed to the model at a specific angle. It is the same effect as if the model would be rotated on the representation table. However, if the model is too large for the representation table, it cannot be captured completely. Here, the light deflector ??????can be used.light angle device put in a slot before the left lamp like a “filter disc”.

    The light angle device exists of many, angled, arranged “mirrors”. The advantage is the registration of parallel structures going in the same direction of the representation table. Even canvas models that show structures in both directions can be captured excellently.

    The upper edge of the suction plate of all scanners that are bigger than size CS285, is not completely illuminated (about 15 cm). The overall width, not length, thus is limited in favor of this effect only at the larger scanners from CS285.

  • Höhenausgleichsprogramm
    Mit dieser Option lassen sich gerahmte Bilder je nach Scannertyp bis zu 15 cm Höhe belichtungs- und schärfeausgleichend scannen.

    The program is put into effect when, for example, a framed picture, of which the actual image information has a greater height than the highest point of the frame. All parameters of the scanner are automatically set into this situation. The operator does not have to adjust the appropriate exposure. Only the original thickness (height) and the height of the frame must be entered in addition to the original width and length.

    Thereby, the exposure lamps are driven to a level that permits the passing of the photo frame, whereas the focus remains on the image and the required exposure compensations are monitored and controlled with the exposure time from a computer.

  • VACUUM PLATE
    Original plate with a vacuum device for drawing models, optionally available with zone regulation

    The perforated magnetic disk is provided as a vacuum board, in which the central suction can be adjusted. Vacuum panels are available up to A0 and higher, optionally via a zone regulation. This allows flat models that do not lie flat, be sucked.

  • ADDITIONAL LIGHTS FRONT AND REAR
    Option to produce a three-dimensional impression

    The four lamps (L_R_V_H; left-right-front-back) can illuminate for example three-dimensional models “all round”, as if in a light tent. In connection with the optional variable reproduction angle the plastic effect of the scan result can be reinforced.

    The lamps can be switched on individually. For special requests in the illumination, especially when scanning woods, respect of longitudinal structures may be considered individually.

    IMG_2770-1

  • LOADING POSITION
    In ST-scanners, the lamps and the platen can be driven entirely aside to allow free space for placing the items.

    When operating this control panel in the software user interface, the lamps go to the furthest left position at the CS ST Repro Decor scanner, in the center position at the CS ST VR scanner. The support table moves to the farthest end position on the right side.

    So you can put valuable item without having to slide them under the exposure lamps, onto the free support table from above; when necessary using a forklift to lift e.g. heavy granite plates, up to approximately 400 kg.

  • LIGHT BOX
    Optional backlight units for KB-slide, glass negatives, aerial photographs and film models up to 1 x 2 m.

    Light boxes are available in different sizes, depending on the application.

  • UV FILTER
    Option to minimize the light stress on archive material

    The insertable front of the lamps filter discs reduce the already small proportion of the UV lamps used additionally to a minimum.

  • POLARIZING FILTER
    Filter to turn off unwanted reflections

    Only available for special applications on request.

  • BOOK CRADLES
    Option for scanning books. 90 ° -180 ° book cradle , 180 ° book cradlem manual or motorized

    Various book cradles are available. 180 ° -Book cradle for normal use under glass or without glass. 90 ° / 120 ° book cradle for the book sound use, can be used with or without glass plate.

    The book cradles are always equipped in the basic version with manual height adjustment for the gentle pressure against the glass plate or for height adjustment.The support surface is provided with a resilient foam pad. According to the spine width, the two bearing surfaces can be adjusted in the 180 ° version against each other.The motorized model is available for both the glass plate as well as for height adjustment.

  • ADDITIONAL SOFTWARE PACKAGE
    Optional:
    Continuous scan, lapel scanning and more to increase productivity. Modularly available on request.
  • GLASS, GLASS MOTOR
    Optional when archival may be pressed against a glass plate. Manual or motorized.

    The manual or electric pivoting glass plate provides in the locked working position for flatness of the model (eg. open book). For some types of scanners it is removable and allows scanning originals without glass contact pressure.